高铝粉煤灰提取氧化铝后硅钙渣用作水泥混合材

为了使高铝粉煤灰提取氧化铝后所产生的硅钙渣被大量的用作水泥混合材,通过水泥强度、水化放热和干缩性实验研究了原状硅钙渣和脱碱硅钙渣对水泥强度和稳定性的影响。结果表明,当硅钙渣掺量达30%时,硅钙渣水泥强度仍可满足P·C 32.5水泥要求。且随硅钙渣掺入量的增加,水泥早期水化放热速率增加的同时水泥累计水化放热量和干缩率还会显著降低。与原状硅钙渣相比,在同等掺量的情况下,脱碱硅钙渣更有利于保持水泥强度,降低其水化热和改善干缩性。     

密相塔半干法烟气脱硫塔内加湿降温及其对脱硫效率的影响

为了实现密相塔半干法脱硫工艺的精确加湿进一步提高系统脱硫效率,利用推导出的传热传质计算方法,得到烟气温度降低和加水量的关系.结合3组密相塔半干法工程实际数据,发现理论计算值和实测值误差区间仅为2.9％ ～5.4％.通过选取河北某钢厂210 m2烧结烟气密相塔半干法脱硫项目实际在线检测数据,发现循环脱硫灰含湿量为3％的系统脱硫效率整体高于含湿量为5％和4％的样品,最大值达93.56％.通过粒度分析、扫描电镜、X射线衍射及差热-热重对2种不同含湿量的循环脱硫灰进行表征,结果表明,含湿量为3％的循环脱硫灰较含湿量为5％的样品粒径小、比表面积大,无团聚现象,物相分析还证实相对于含湿量为5％样品,其Ca(OH)2和结晶水含量少,几乎都是CaSO4和CaS03干态物质,因此脱硫反应进行彻底,脱硫效率较高.     

重点流域水系沉积物中多环芳烃标准样品制备

环境标准样品是监测过程中重要的质量控制手段,中国受天然基体标准样品制备技术的制约,尚未拥有自己的沉积物中多环芳烃标准样品。为制备符合中国重点流域沉积物类型及多环芳烃浓度水平的沉积物标准样品,对中国6个重点流域的沉积物进行了采样,获得了制备多环芳烃标准样品的原料。分析常温及冷冻2种干燥方式对多环芳烃的影响,为制备大批量多环芳烃标准样品提供数据支持。对11个点位样品采用气相色谱质谱法测定16种优控多环芳烃化合物浓度,结果表明,样品均匀性良好,样品中多环芳烃检出率在99%以上,江河沉积物样品中多环芳烃浓度区间为664~2.91×103μg/kg,湖泊样品最高值达到1.25×105μg/kg,其主要污染源是化学燃料的燃烧。为中国制备水系沉积物中多环芳烃标准样品积累了技术基础。     

Effect of pipes in heat pump system on electric vehicle energy saving

ABSTRACT

Refrigerant pressure drop and temperature change in pipes are normally ignored in the thermodynamic analysis of traditional vehicle air conditioning system, this will result in serious errors. In this Paper, pressure drop and temperature difference are simulated in different pipes of electric vehicle (EV) heat pump system to analysis the effects of pipes in the actual EV heat pump system. The results indicate that the greater the mass flow, the faster pressure drop increases, the temperature difference decreases. Pressure drop of saturated liquid refrigerant is smaller than that of saturated gas refrigerant at the same saturation pressure and mass flow rate. The higher the refrigerant pressure (no phase change), the slower pressure drop decreases, the faster the temperature difference decreases. Pressure drop decreases with the increment of bending angle of the pipe. For EV heat pump system, suitable valves and less branches are helpful for energy saving of the system. Shortening the pipe between compressor and condenser can reduce temperature change obviously. Pressure drop per unit length in the pipe between evaporator and compressor is large especially in heating mode because of lower refrigerant density. It even reaches to over 100 times of that in the pipe between condenser and throttle valve in heating mode and has negative effects on the performance of the system. If the evaporator is closer to the compressor and the number of branches is less, then pressure drop will decrease a lot, which will be advantageous for energy saving of the heat pump system.     

Study of the performance of a coolant mixed with an Al2O3/SiC nanomaterial in an engine radiator

One of the important components of a car to control the temperature of a car's engine is the radiator. To increase the heat absorption capacity of the coolant/fluid used in the radiator with minimum pumping power, innovative fluids called nanofluids have become the main area of research these days. Therefore, with the development of new technologies in the field of “nano-materials” and “nano-fluids,” the physical and chemical properties of coolant/fluid can be improved which in turn improves the radiator and engine efficiency, and reduces radiator weight and size. In this article, the heat transfer by forced convection in nanofluids based on Al₂O₃ and SiC was studied experimentally and compared to that of base fluid in an automotive radiator. The nanofluid is mixed with ethylene glycol and the fluid is prepared by the sonication method. The nanofluids were prepared by varying the nanomaterials and the amounts of nanomaterials in the base fluid and their heat transfer performance in the radiator was analyzed using ANSYS FLUENT software. Approximately 15% and 12% increase in radiator efficiency by using Al₂O₃ mixed nanofluid and SiC mixed nanofluid, respectively.     

Experimental thermal storage research of organic binary phase change materials in building environment

This paper aims to reveal the heat transfer mechanism of low-temperature phase change material (PCM) and design PCM heat storage device in building heating environment. Firstly, low-temperature binary PCMs of lauric acid and stearic acid are prepared, and their thermal properties are investigated by DSC. Then, shell and tube latent heat thermal energy storage units are conducted, and heat transfer experiments are carried out to analyze the heat transfer mechanism of PCM. The results demonstrate that natural convection plays an important role in heat transfer process, and the heat storage efficiency of PCMs can be significantly enhanced by increasing the fin width and improving the inlet heat transfer fluid (HTF) temperature. Furthermore, some proposals are put forward to guide the design of PCM storage device in building heating environment.     

The determination and matching analysis of pinch point temperature difference in evaporator and condenser of organic rankine cycle for mixed working fluid

Exergo-economic analysis of the pinch point temperature difference (PPTD) in both evaporator and condenser of sub-critical organic Rankine cycle system (ORCs) are performed based on the first and second laws of thermodynamics. Taking mixture R13I1/R601a as a working fluid and the annual total cost per net output power Z as exergo-economic performance evaluation criterion, the effects of PPTD in evaporator ΔT_e, and the PPTD ratio of condenser to evaporator y, on the exergo-economic performance of ORCs are analyzed. Moreover, how some other parameters influence the optimal PPTD in evaporator ΔT_e,opt and the optimal PPTD ratio of condenser to evaporator y_opt are also discussed. It has been found that the exergo-economic performance of ORCs is remarkably influenced by ΔT_e and y, and there exists ΔT_e,opt and y_opt. In addition, ΔT_e,opt and y_opt are affected by heat transfer coefficient ratio of condenser to evaporator ß, the temperature of working fluid at dew point in condenser T_1a, and composition of R13I1/R601a: larger ß and T_1a lead to lower ΔT_e,opt and y_opt; by contraries, larger mass fraction of R13I1 makes ΔT_e,opt and y_opt increase, and y_opt increases linearly. The effects of the temperature of working fluid at bubble point in evaporator T_3a, mass flow rate of exhaust flue gas m_g, and inlet temperature of exhaust flue gas T_gi on ΔT_e,opt and y_opt are very slight. For comparison, three additional working fluids, namely R601a, R245fa, and 0.32R245fa/0.68R601a, are also taken into account.     

中国工业CO_2排放的行业间传导网络及协同减排

工业是碳排放的主要部门,科学识别工业CO_2排放的行业间传导并揭示其联动结构对于跨行业协同减排具有重要的理论和现实意义。本文基于1991-2012年中国工业36个两位数行业数据,在VAR模型框架下,利用Granger因果检验方法对CO_2排放的行业间传导关系进行了识别,并从关系视角出发,借助社会网络分析方法(SNA)揭示工业CO_2排放行业间传导的整体和个体网络结构特征,研究发现:工业CO_2排放的行业间传导呈网络结构形态,网络密度在1-6期的滞后阶数下呈先升高后下降的趋势,并且在滞后2期达到最高;燃气生产和供应业、电力热力生产和供应业、服装业、造纸及纸制品业、木材加工业具有较高的度数中心度、中介中心度、接近中心度,在网络中处于核心位置,并发挥中介和桥梁作用;在CO_2排放的行业传导网络中,煤炭采选业、黑色金属矿采选业、有色金属矿采选业等10个行业属于经纪人板块,医药制造业、饮料制造业、化学纤维制造业等9个行业属于净受益板块,金属制品业、塑料制品业、农副食品加工业等11个行业属于双向溢出板块,烟草加工业、石油加工及炼焦业、燃气生产和供应业等6个行业属于净溢出板块。基于上述结论,本文提出了工业CO_2排放的跨行业协同减排思路。     

Heat as emergency,heat as chronic stress: policy and institutional responses to vulnerability to extreme heat

Increasingly commonplace in cities, extreme heat events introduce multi-stress vulnerability, affecting people’s health and well-being, financial situation, mobility, social relations, and access to basic services. Planning to reduce heat vulnerability has become part of government business and to some extent community-level responses, cutting across a number of sectors including public health, emergency management, social services, critical infrastructure, and housing. This planning is often framed around heat as an emergency, focusing on preventing loss of life and severe health impacts, yet a vulnerability perspective also draws attention to the chronic and persistent impacts of heat. Our research, based on interviews and desktop research in Melbourne, Australia, found tensions between addressing heat as an emergency and heat as a source of chronic stress, with emergency responses taking precedence over responses addressing the chronic dimensions of heat. Each approach results in different but nonetheless related programmatic priorities for reducing vulnerability. In complex institutional settings, improving relations between policy and programme managers, non-government organisations, and vulnerable people themselves would enable the multiple stresses associated with extreme heat to be more effectively addressed. Policy and institutional responses that better appreciate the interconnections between the emergency and chronic aspects of heat would likely reduce vulnerability and contribute to more just approaches to urban sustainability.     

The impact of the electricity tariff reform on renewable energies and energy efficiency investments: The case of the Italian residential market

This article investigates the impact that the electricity tariff reform is likely to have on investments in renewable energies (i.e., photovoltaics) and the adoption of energy efficiency measures (i.e., installation of heat pumps and efficient home appliances) in the residential market in Italy. The study develops detailed cost comparisons and simulations considering two different investment scenarios (before and after the reform) to conclude that the reform will: (i) have a negative impact on investments in photovoltaic systems; (ii) favor the adoption of energy efficiency measures, such as efficient home appliances.